Skip to content

How to digitize a logo for embroidery

To digitize a logo, you redraw it as shapes at the size it will be sewn, give every shape a stitch type (a running stitch for thin lines, satin for narrow columns and lettering, a fill for wide areas), set the stitch direction, underlay and pull compensation, put the colours in sewing order with as few trims as possible, and save the file in your machine's format. You can do it in software, pay a digitizer, or let an automatic digitizer make the first pass.

1. Prepare the logo

Decide the finished size and the fabric first, because every later choice depends on them. A logo digitized for a 90 mm chest sews badly at 250 mm on a jacket back, and a towel needs a different underlay than a polo.

Then simplify the art for thread:

  • Flat colours. Gradients, shadows and photo textures have no stitch equivalent; replace them with solid areas. Every colour is a thread change on the machine.
  • Lettering at least 0.25 inch (about 6 mm) tall. Printful and Custom Ink both use this as their minimum for flat embroidery.
  • Lines at least 0.05 inch (about 1.3 mm) wide. Thinner lines either vanish or turn into a wobbly running stitch; the same two guides give this minimum.
  • No detail smaller than the thread. Tiny gaps between letters and dots under a millimetre close up once the thread pulls the fabric.

2. Pick a stitch for each shape

Shape Stitch Rule of thumb
Thin lines and fine outlines Running or bean stitch One or three passes along the line
Narrow columns, borders, lettering Satin About 1 mm to 8–10 mm wide (Graphics Pro); wider satins leave long loose stitches that snag
Wide areas Fill (tatami) Rows of short stitches at one angle; change the angle between neighbouring areas so they read apart

Ink/Stitch's documentation describes satin columns as the stitch for "borders, letters or small fill areas". The stitch direction matters as much as the type: thread catches the light along its length, so two areas sewn at different angles look like two shades of the same colour.

3. Set underlay and pull compensation

Stitches pull the fabric in. As the Ink/Stitch documentation puts it, satin stitches "pull the fabric together, resulting in a column narrower than you draw". Pull compensation widens each column by a fraction of a millimetre to make up for it.

Underlay is a light layer sewn first to hold the fabric flat and lift the top stitches. Ink/Stitch lists three kinds for satin: a centre walk for thin columns, a contour for small and medium ones, and a zig-zag, often combined with the other two, for wide columns or difficult fabrics. Stretchy knits and towels need more underlay than a woven cotton.

4. Plan the order, jumps and trims

The machine sews one colour at a time and moves between shapes with jumps. A DST file cannot store a single stitch longer than 12.1 mm, so longer moves become jumps; a long jump left uncut is a loose thread across the design.

A Tajima operator we work with gives a simple rule: a move of 2 to 3 mm can stay a jump, anything longer gets a trim or a travel run hidden under the next shape of the same colour, and a 250 mm jacket back should need no more than 40 to 50 trims. Every trim stops the machine and adds a tie-off, so a file with hundreds of them costs real machine time. Sewing the shapes of one colour in an order that keeps the moves short is what keeps the trim count down.

5. Save, check and sew a test

Save the file in the format your machine reads; the formats by machine table lists them, and DST is the default for commercial multi-needle machines. Keep the source file too: a stitch file scaled by much keeps its old stitch count and density, so a new size means digitizing again rather than stretching the file.

Before production, open the file in the embroidery file viewer to check the size, stitch count and colour changes, then sew a test on the same fabric and stabiliser you will use.

Three ways to get it done

Way Cost Time Best for
Software, yourself free (Ink/Stitch) to a professional suite days to learn, then minutes to hours a design people who digitize often and want control; see the software comparison
A digitizer about $10–25 for a simple logo; costs by country usually within a day complex art, photos, small lettering
An automatic digitizer a few dollars a design or a monthly plan minutes logos with flat colours and clean edges

Embrodo is an automatic digitizer: you upload the logo, give the width, the placement and the fabric, and get a stitch preview and the stitch count before you download the file in your machine's format.

Questions

Can I digitize a logo for free?

Yes. Ink/Stitch is a free, open-source extension for Inkscape that runs on Windows, macOS and Linux and writes DST, PES, JEF, EXP, VP3 and more. You draw or trace every shape and choose its stitch yourself, so expect to spend a few evenings learning it.

How long does it take to digitize a logo?

A digitizer usually delivers a simple logo within a day; many services quote 4 to 12 hours. Doing it yourself takes longer the first few times. An automatic digitizer gives a first file in minutes, which you then check against the preview.

Can I digitize a PNG or JPG?

Yes, but the picture is only the guide: every shape is redrawn as stitches. A clean image with flat colours and sharp edges gives the best result. A blurry or tiny image makes the digitizer guess, so send the largest version you have.

Why does my logo look different once it is sewn?

Thread has a width and pulls the fabric. Shapes come out narrower in the direction of the stitches, small gaps close up and tiny text fills in. Pull compensation, underlay and leaving out detail smaller than the thread can show are what keep a sewn logo close to the drawing.

Your first design is on us.

Upload a logo and see the stitch preview. No card needed.

Upload an image
Stitch preview of the Ridgeview Eagles chest logo